编程器、河洛、ELNEC编程器、烧录器、IC测试座、逻辑分析仪、IC代烧、FlashRunner ISP烧录器- 深圳市浦洛电子科技有限公司

ALL-100 常见问题解答

Q01 : What's the difference between ALL-100 & ALL-11P3?

A01 : ALL-100 is our latest Universal & Gang Programmer. Its operation is similar to ALL-11P3, but ALL-100 has built-in USB2.0 port for the highest transmission up to 480Mbit/sec.. Moreover, the controller uses 16bit/96MHz MCU which improves performance significantly.

Q02 : Can my PC install ALL-100?

A02 : Currently the OS supported are Windows 98 SE / ME / 2000 SP4 / XP SP1 / 2003 server or later version, and the hardware supported covers USB1.1 & USB2.0. USB2.0 is recommended for the highest performance.

Q03 : Why doesn't ALL-100 work after installation?

A03 : Under OS Win 2000, please make sure the system had been upgraded to SP4; under OS Win XP, please make sure the system had been upgraded to SP1.

Q04 : What is the range of programming voltage offered by ALL-100?

A04 : VCC: 1.8V~5V; VHH: 5V~12V; VOP: 9V~25V. Furthermore, the prog. voltage and I/O voltage are separated.

Q05 : Does ALL-100 just program one device at a time?

A05 : No! At present, ALL-100 can program 1 or 4 or 6 or 8 devices simultaneously with different module mounted.

Q06 : What is the difference between Single Socket Module & Gang Module?

A06 : Single Socket Module can only program one device at a time, but Gang Module can program 4 or 6 or 8 devices simultaneously.

Q07 : Besides USB transmitting interface, does ALL-100 support other else?

A07 : No! Currently ALL-100 only supports USB interface.

Q08 : May I use the previous adapter to run ALL-100?

A08 : Yes, most of the previous adapters still work well on ALL-100.

Q09 : Does ALL-100 support ISP (in-circuit programming)?

A09 : No, generally we don't recommend! Wired out to PCB from ALL-100 may cause power current insufficient.

Q10 : What shall I do when the message "Module Error!" appears?

A10 : It means the Module currently mounted on ALL-100 does not match the correct Module it should be used for ICs to be programmed. Please check for appropriate Module P/N.

Q11 : Is one PC only able to connect to one set of ALL-100?

A11 : No! One PC can connect to utmost 8 sets of ALL-100.

Q12 : How can I identify each ALL-100 when several sets of them are connected to the same PC?

A12 : The "SITE#" on rear panel of each programmer provides user to identify the order of programmer from #1 to #8 and the #number can not be repeated in the system.

Q13 : Can each ALL-100 program different IC type when several sets of them are connected to the same PC?

A13 : No! All of the connected programmers can only program the same IC type simultaneously.

Q14 : My PC has USB port and the OS also had been upgraded, but ALL-100 still can't work. What shall I do?

A14 : Various motherboards in the market have somewhat different feature and cause compatibility problem. So choose our identified PCI to USB2.0 Card or USB2.0 Hub to avoid the problem.

Q15 : Does each pin built in ALL-100 provide the complete Pin Driver signals?

A15 : Yes, each pin can provide 16 functional signals such as VCP, VHH, VOP, TTLHi, TTLLo, CAP, Oscillator, etc.

Q16 : Can't find my desired IC Type from the device list. Does that mean it isn't supported?

A16 : Mostly we are willing to support programming software for the new devices. Depending on chip complexity, usually it takes 2~3 weeks. The process can be shortened if customer can provide 8~10 samples for testing. In most cases, an existing adapter/converter can support new devices as well, but sometimes a new adapter is required. We try to cover a broad range of IC types into our device list; however, some devices may hardly be supported due to the complexity or less demand.

Q17 : How to download programming file?

A17 : 1. Download the complete set of programming file - ALL100.EXE2. Executing and unzipping the file ALL100.EXE, then executing the file SETUP.EXE. For single socket module (M1-XXX-XXX Module):
ftp://ftp.hilosystems.com.tw/pub/download/all100/ALL100.EXE
For gang module (M4-XXX-XXX or M8-XXX-XXX Module):
ftp://ftp.hilosystems.com.tw/pub/download/all100gang/ALL100GANG.EXE

Q18 : How to run self-diagnostics?

A18 : You may run the simple tester diagnostics according to the instruction below:
* Please dismount Module before test!